FSFabShopSource

Angle Iron Sizes and Weights Chart

Angle iron sizes and weight per foot for common equal and unequal leg steel angles, how sizes are written, and a quick formula to calculate any angle weight.

Angle iron (steel angle) is the most common shape in a fab shop after flat bar and tube. It shows up in frames, brackets, ledgers, shelf supports, gate frames, stair stringer clips and base plates. This guide explains how angle sizes are written, gives a quick weight chart for common sizes, and shows how to work out the weight of any angle in a few seconds.

How angle sizes are written

An angle is called out as leg x leg x thickness, all in inches. 4 x 4 x 1/4 is an equal leg angle with two 4 in legs and 1/4 in thickness. On structural drawings you will usually see it written as L4x4x1/4.

Small angles (legs under 3 in) are often sold as "bar size" angles, while 3 in and larger are structural sizes. Suppliers commonly stock angle in 20 ft lengths, with some sizes also available in 40 ft. Check your supplier's stock list before you build a cut list around a length.

Angle iron weight chart (lb per foot)

Weights below are for carbon steel angle, rounded to two decimals. Use them for estimating, freight and handling. For the full list of sizes, see the steel angle weight chart.

Size (in)lb/ft20 ft stick (lb)
1 x 1 x 1/80.8016.0
1-1/2 x 1-1/2 x 1/81.2224.4
1-1/2 x 1-1/2 x 1/42.3446.8
2 x 2 x 1/81.6533.0
2 x 2 x 3/162.4348.6
2 x 2 x 1/43.1963.8
2-1/2 x 2-1/2 x 1/44.0480.8
3 x 3 x 3/163.7174.2
3 x 3 x 1/44.8997.8
3 x 3 x 3/87.18143.6
4 x 4 x 1/46.59131.8
4 x 4 x 3/89.73194.6
4 x 4 x 1/212.76255.2
6 x 6 x 3/814.84296.8
3 x 2 x 1/44.0480.8
4 x 3 x 1/45.74114.8
6 x 4 x 5/1610.30206.0
6 x 4 x 3/812.28245.6

Published mill tables can differ slightly in the last decimal because of fillet radius and rounding. For structural design, use the values in the AISC Steel Construction Manual or your supplier's mill certs.

How to calculate angle weight yourself

If you need a size that is not on the chart, you can get very close with a simple formula. Steel weighs about 0.2836 lb per cubic inch, which works out to about 3.40 lb per foot for every square inch of cross section.

Area (sq in) = thickness x (leg A + leg B - thickness)

Weight (lb/ft) = Area x 3.40

Example, 4 x 4 x 1/4: area = 0.25 x (4 + 4 - 0.25) = 1.94 sq in. Weight = 1.94 x 3.40 = 6.59 lb/ft. A 20 ft stick is about 132 lb.

Example, 6 x 4 x 5/16: area = 0.3125 x (6 + 4 - 0.3125) = 3.03 sq in. Weight = 3.03 x 3.40 = 10.30 lb/ft.

This ignores the small fillet in the corner, so it can be a hair under the mill table weight, but it is well within what you need for a quote. The steel weight calculator does the same math for any size and length.

Choosing a size

Using angle weights in a quote

Once you have your cut list, total the length of each size, multiply by lb/ft, and you have a material weight for the job. Add drop: running your cuts through the cut list optimizer tells you how many 20 ft sticks to buy, which is what you actually pay for. Then carry the material cost into the quote builder along with labor and markup.

For frames with mitered angle corners, the miter cut calculator gives cut lengths and angles, and Pro can nest mitered parts on sticks to cut down waste.

Frequently asked questions

How much does 4 x 4 x 1/4 angle iron weigh per foot?

About 6.6 lb per foot, so a 20 ft stick weighs roughly 132 lb. Use your supplier's mill table for exact values.

Which leg is listed first on an unequal angle?

The long leg is listed first. A 6 x 4 x 5/16 angle has a 6 in leg, a 4 in leg, and 5/16 in thickness on both legs.

More guides